Search found 997 matches

by 69brightbluebronco
Fri Feb 18, 2011 8:23 am
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: wanted main tank sending unit
Replies: 10
Views: 6401

just checked online,
they are different sending units for front and rear tanks. so that wont work stan. thanks anyways.
by 69brightbluebronco
Thu Feb 17, 2011 3:24 pm
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: wanted main tank sending unit
Replies: 10
Views: 6401

im not sure if they are different senders or not.
ill have to find out.
by 69brightbluebronco
Thu Feb 17, 2011 11:09 am
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: wanted main tank sending unit
Replies: 10
Views: 6401

wanted main tank sending unit

looking for a rear tank (main) sending unit, dont need the float, but i need a working unit, can be a little dirty but the one i pulled was so coated, it was unusable. so a nice used one would be great...

thanks
by 69brightbluebronco
Wed Feb 16, 2011 8:11 am
Forum: Drivetrain and Suspension
Topic: What Transmission?
Replies: 7
Views: 6080

for an NP 435 you need a body lift of some kind, 1 inch minimum, i think 2 inch is preferred. and a different intermediate housing between it and the dana 20 C4 and C6 are ford auto transmissions, you can use those if you want to go auto there is also the NV3550 and 4500 transmissions too not sure w...
by 69brightbluebronco
Fri Feb 11, 2011 5:04 pm
Forum: Shootin' the Breeze
Topic: Kyle Porth
Replies: 3
Views: 3161

im great i know :)
by 69brightbluebronco
Tue Feb 08, 2011 5:23 pm
Forum: Electrical and Auxiliary equipment
Topic: 3g help
Replies: 5
Views: 4868

http://www.bcbroncos.com/3G%203%20wire%20with%20water%20mark.pdf this should help also i dunno where the alt is on a windstar but on the taurus/sable 3.0 it is right on top of the engine and easy to access/unbolt. 3G 130amp Donor Vehicles: (1994-95) Ford Mustang 5.0L (1994-00) Ford Mustang 3.8L (199...
by 69brightbluebronco
Fri Feb 04, 2011 7:02 pm
Forum: Shootin' the Breeze
Topic: Toms Bronco Parts Link
Replies: 2
Views: 2495

first thing i noticed when i logged on too.
cool!
by 69brightbluebronco
Fri Jan 28, 2011 2:27 pm
Forum: Shootin' the Breeze
Topic: Need a little help
Replies: 2
Views: 2255

the first pair on the yellow bronco are probably mickey thompson classic II without the beadlock rings

http://www.mickeythompsontires.com/newp ... e.php?id=4
by 69brightbluebronco
Wed Jan 26, 2011 5:38 pm
Forum: Steering, Brakes, Wheels and Tires
Topic: Dana 44 w/ Disc Brakes and Upgraded Steering
Replies: 10
Views: 12150

you can do either disc swap (ford or Chevy) on either axle i believe
by 69brightbluebronco
Wed Jan 26, 2011 8:09 am
Forum: Drivetrain and Suspension
Topic: need a schematic for warn hubs
Replies: 14
Views: 9526

thats special
by 69brightbluebronco
Mon Jan 24, 2011 5:02 pm
Forum: Drivetrain and Suspension
Topic: need a schematic for warn hubs
Replies: 14
Views: 9526

i have a pdf of instructions from warn
email if you want it
bluebronco69 at hotmail.com
by 69brightbluebronco
Sat Jan 22, 2011 8:59 am
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: Full Hard Top Needed
Replies: 14
Views: 9967

there is a top in oregon city for 250, i dunno if you have seen it or not:

http://portland.craigslist.org/clc/pts/2173652578.html
by 69brightbluebronco
Thu Jan 20, 2011 8:18 am
Forum: Shootin' the Breeze
Topic: Shawn- LoLo Pass ?
Replies: 24
Views: 10952

on this site i am on they were talking about the hood river route possibly being open and passable, but they arent sure if thats true or not. apparantly they are hacking out a quad trail for people to get in an out without going to hood river.... http://www.pnwadventures.com/forum/completed-trips/23...
by 69brightbluebronco
Mon Jan 17, 2011 1:51 pm
Forum: Shootin' the Breeze
Topic: Is this Saddle Up's Bronco for sale?
Replies: 4
Views: 2712

do it juggy
by 69brightbluebronco
Sat Jan 15, 2011 8:20 pm
Forum: Shootin' the Breeze
Topic: Tmaxx 2.5 for sale
Replies: 0
Views: 1632

Tmaxx 2.5 for sale

see ad here: http://corvallis.craigslist.org/for/2160094268.html i will cut a good deal for anyone on here. http://images.craigslist.org/3nd3p63o45Y45P05X1b1e584baddd12db13fa.jpg http://images.craigslist.org/3m93oa3l45T25Q35Z5b1e06a6458aab191224.jpg its in great shape, some extra parts, and upgrades.
by 69brightbluebronco
Thu Jan 13, 2011 12:35 pm
Forum: Drivetrain and Suspension
Topic: Ron Davis lower Radiator hose?
Replies: 2
Views: 3461

i have a mustang waterpump with serp. and i am using the bronco radiator, and they are the same diameter.
i cant help you with the hose situation though, as the bronco rad. has the lower hose on the pass side, and the mustang waterpump is on the driver side, so i had to do some custom hose work.
by 69brightbluebronco
Sun Jan 09, 2011 9:35 am
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: EB parts
Replies: 0
Views: 1805

EB parts

for sale in la center WA.
seems like some pretty good prices
not my stuff!
but good deals for the trim pieces...

http://portland.craigslist.org/clk/pts/2151150856.html
by 69brightbluebronco
Fri Jan 07, 2011 10:32 am
Forum: Bodywork, Paint, Cages, Specs, OEM, Dash
Topic: Home from the body shop after 2 years!
Replies: 21
Views: 25527

On that note, what color are the inside of the tailliht buckets supposed to be? I blasted out some really crappy flat white paint that sure looks to be original, but I can't tell for sure. The headlight buckets were all black and will be again. i got a can of chrome colored spray paint when i paint...
by 69brightbluebronco
Wed Jan 05, 2011 2:24 pm
Forum: Electrical and Auxiliary equipment
Topic: electric choke power source
Replies: 12
Views: 10280

double check the green with red stripe.
but im pretty sure thats the one, and it has power with the key on. and its close to the engine too so its convenient.
by 69brightbluebronco
Wed Jan 05, 2011 11:20 am
Forum: Electrical and Auxiliary equipment
Topic: electric choke power source
Replies: 12
Views: 10280

most after market carbs need 12 volts for the electric choke, while some factory elec choke need 6v. thats why you have heard of hooking it to the STA terminal. do you have the stock alternator? or 3G? if it is the stock alt. then use the green with red stripe wire that hooks up to the voltage regul...
by 69brightbluebronco
Thu Dec 30, 2010 8:11 am
Forum: Drivetrain and Suspension
Topic: Repair manual for A4LD transmission
Replies: 2
Views: 4041

here is a good article about someone rebuilding a beefing up an a4ld on explorer forum: http://www.explorerforum.com/forums/showthread.php?t=98027 also i would search therangerstation.com useful info there. here is a pdf i found. titled technical service information. http://sierraautomatico.files.wo...
by 69brightbluebronco
Wed Dec 29, 2010 8:14 am
Forum: Electrical and Auxiliary equipment
Topic: Battery keeps draining in just a few hours?
Replies: 5
Views: 4589

pull the negative cable. then set your handy volt meter to measure ohms. put that inline with the batter and the negative cable that you just removed. start unplugging things and pulling fuses until the amp reading drops to nearly zero. if you have an after market radio with a clock and preset stati...
by 69brightbluebronco
Wed Dec 29, 2010 8:12 am
Forum: Shootin' the Breeze
Topic: Junkass lookin heater core
Replies: 13
Views: 11715

they shoudl have a generic rubber elbow in that size i then used a small section of copper pipe i had to connect the end of that elbow to the a longer section of hose to make the rest of the run.
by 69brightbluebronco
Thu Dec 16, 2010 12:55 pm
Forum: Shootin' the Breeze
Topic: Budget Island Garage
Replies: 7
Views: 5706

i would look for a simple roll bar, 4 point style, and then you could use a bikini style top, or if you dont want to buy one of those new. i dont know how a j**p bikini top would fit, but im sure its adaptable.
by 69brightbluebronco
Tue Dec 14, 2010 8:31 am
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: WTB liftgate arm
Replies: 6
Views: 2598

yes. toms bronco parts should have a kit. as well as all the other suppliers
by 69brightbluebronco
Mon Dec 13, 2010 10:42 am
Forum: Bodywork, Paint, Cages, Specs, OEM, Dash
Topic: Manual Windshield Wipers
Replies: 21
Views: 19207

ha, and believe it or not i have used that little modification in the past. after my bronco was first completed and on its first trip to sandlake, dad was driving, and it was a huge down pour somewhere in the coast range headed to tillamook. well the little clip that holds the linkage together decid...
by 69brightbluebronco
Mon Dec 13, 2010 8:17 am
Forum: Bodywork, Paint, Cages, Specs, OEM, Dash
Topic: Manual Windshield Wipers
Replies: 21
Views: 19207

unhook the linkage from your electric wiper motor, and proceed to move linkage left to right by hand. cost 0$ time 30 seconds to undo "c" clip

why buy a kit?
by 69brightbluebronco
Fri Dec 10, 2010 11:00 am
Forum: Drivetrain and Suspension
Topic: bloody knuckle garage
Replies: 28
Views: 19670

some duffs arms for sale in eugene
http://eugene.craigslist.org/pts/2096540710.html

actually i think thats for the rear axle...
my bad
by 69brightbluebronco
Fri Dec 10, 2010 8:50 am
Forum: Bodywork, Paint, Cages, Specs, OEM, Dash
Topic: crabwerks roll cage
Replies: 14
Views: 9674

i wasnt sure about his cages so i didnt want to mention it, but he could build and weld it all for you, and you can drive down and drop it in place, much easier then any shipping, or you having to do the welding...
by 69brightbluebronco
Thu Dec 09, 2010 10:13 am
Forum: Drivetrain and Suspension
Topic: bloody knuckle garage
Replies: 28
Views: 19670

http://broncobob.com/

they have weld on shock hoops, not sure on quality, but they are close by i bet you can drive down and get them today.
(albany OR)
by 69brightbluebronco
Thu Dec 09, 2010 9:06 am
Forum: Steering, Brakes, Wheels and Tires
Topic: help w/disc brake parts id
Replies: 5
Views: 5123

yea i tried googling those numbers and searching and came up with nothing.
by 69brightbluebronco
Tue Nov 30, 2010 3:27 pm
Forum: Electrical and Auxiliary equipment
Topic: Headlight problems?
Replies: 34
Views: 26328

i have heard good things about this kit
http://www.eautoworks.com/product-eAuto ... 189849.htm
headlight relay harness for 20$ plus shipping....
by 69brightbluebronco
Mon Nov 15, 2010 1:20 pm
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: Dana 44
Replies: 2
Views: 1944

sent you an email
by 69brightbluebronco
Fri Nov 12, 2010 11:17 am
Forum: Bronco Parts: Buy, Sell, Trade, Mass Buy
Topic: Dana 44
Replies: 2
Views: 1944

Dana 44

hey guys ive got a ford dana 44 front i dont need anymore i already took the disc brakes, knuckles spindles etc. its still got the gears, 350 i think. and axle shafts, i need to check and see if its bronco width or full width. has c wedges for radius arms. and if you want/need i can include drum knu...
by 69brightbluebronco
Fri Nov 05, 2010 12:09 pm
Forum: Drivetrain and Suspension
Topic: Sputter, Coughing, and Power Loss
Replies: 28
Views: 12763

gunk in the carb bowls?
timing?
by 69brightbluebronco
Thu Nov 04, 2010 12:35 pm
Forum: Shootin' the Breeze
Topic: sandblasting wheels
Replies: 0
Views: 914

sandblasting wheels

anyone have a good connection for sandblasting some wheels for cheap?
they are rusty/flaky chrome.

thanks
by 69brightbluebronco
Wed Oct 27, 2010 7:40 am
Forum: Shootin' the Breeze
Topic: Stroppe Enthusiasts
Replies: 13
Views: 5994

i wish parts were that cheap still
by 69brightbluebronco
Tue Oct 19, 2010 10:16 am
Forum: Steering, Brakes, Wheels and Tires
Topic: Tire size difference
Replies: 6
Views: 6053

235 75 15 is about 29x a little under 9inch wide
30x9.5 will measure less then whats stated on the sidewall, not much. maybe half an inch, but it varies by manufacturer.
but usually interco tires measure over the stated size on the sidewall.
by 69brightbluebronco
Fri Oct 08, 2010 7:23 am
Forum: Shootin' the Breeze
Topic: bronco work day 2.0
Replies: 17
Views: 5516

ok im planning on finishing up the brakes this weekend, so lets cross our fingers, also what kind of rubber lines do i use form the caliper to the axle?
thanks
by 69brightbluebronco
Fri Oct 08, 2010 7:21 am
Forum: Drivetrain and Suspension
Topic: 170 6cyl Carburetor
Replies: 6
Views: 7064

so the carbs all bolt on, they just have different throttle linkage then your original did?